Samsung ML 1610, 2010, 2015, 2510, 2571N fuse

Fuse is needed to reset the counter when a new cartridge is used
This fuse is 250mAh and 3/4" inch long (20 mm) round glass with metal ends. It could be used with Samsung ML-1610 ML-2010 ML2010 ML-2015 ML2015 ML-2510 ML2510 ML-2571N ML2571N series For P/# ML-2010D3 and ML-1610D2 toner cartridge.


Where to buy it: click here

Read More..

Message "096: Fatal Error 02" with Oki printers

096-02 error is a problem with the finisher.
That's a "tray raise or lowering error".

Solution 1:
Check and clean the upper limit switch. 
Solution 2:
Replace the upper limet switch
Solution 3:
Check the shift motor operation and finisher control PCB board. If the motor has failed, you need to replace it, and perhaps the control PCB too. More information click here

Read More..

Canon Pixma MP530 printer

Download:
Cartridges:
Parts:

Troubleshooting:
Error 5B00; the waste ink counter need to be resetted:Turn off the printer
Hold the Resume Button (red circle in the triangle), add a printer (click “Power”) an indicator light green.
Hold the Power Button, release the Resume Button.
Not releasing the Power Button, double click “Resume” and release Both Buttons.
Click “Resume” for Four times
Once you click “Power”, to confirm the selected action (reset counter absorber). To disable the printer “Power” button to click again. More information click here

Read More..

Brother MFC-425CN printer

Download:

Cartridges:

Troubleshooting:
How to reset waste ink counter:Machine off
Switch on the machine while holding down the “menu”button until all the leds are flashing on/off. Now you are in “maintenance” mode.
press 80
press the “mono start” button several times until you see “purge: xxxx”
press “2783” in order to reset the purge counter. You will see: “purge:0000”
press “99” to exit the maintenance mode. More information click here

Read More..

Canon Pixma MP495 printer

Downloads:

Cartridges:

Troubleshooting:
Disconnect the power cable
Hold on "Black", "Color", "Stop/Reset" and "Power" buttons.
Without release them, plug the power cable in. Ink cartridge reset (ship reset):Solution 1 : When "empty cartridge" is displayed, Hold on the "cancel" button until "processing"appears.
Solution 2: Hold on the "Stop" button until "processing" appears Hold on the "Stop" button for 5 seconds. More information click here

Read More..

Reset transfert belt counter on Xerox Phaser 6110 MFP

Sometimes, when you have replaced the Image Transfer Belt, the printer still does not work. You will have to reset the counter.

Procedure:
Enter Service Mode by pressing [MENU] [#] [1] [9] [3] [4] quickly.Select Tech MenuSelect DataSetupArrow to Clear Counts and press EnterEnter Password 1934Arrow to Transfer Belt and press Enter.
The display will show Clearing Counts and then return you to the Tech Menu. Press exit several times to exit the Tech Menu and then power cycle the printer. More information click here

Read More..

How to solve error 6A90 or "APP sensor error" on Canon printers

Error code 6A90 or "APP sensor error" occured during paper feeding or purging.

Solution 1:
check for foreign material or paper debris around the purge drive system unit;
- remove foreign material.
Solution 2:
check for foreign material or paper debris around the ASF unit;
- remove foreign material.Solution 3:
If other solution fail, replace one off the following part- Purge drive system unit
- Logic board. More information click here

Read More..

Error 61.05 on HP Designjet 500, 510, 800

Could appears on HP DesignJets 800 Series, DesignJet 500 and 510.

Printer show a System Error: 61:05

The problem:

That's an error Processing Job.
This Error Code appears in these HP DesignJets with an HPGL/ 2 card installed, when processing either a PostScript or HP-GL/2 file.

Solution 1:
Switch the Printer Off Wait a few minutes. Switch the Printer On Resend the file that you were trying to print. 
Solution 2:
If the Error Code reappears, try to generate the file again and try to print again. If the file that is causing this error is PostScript, check if it is Binary. If the file is Binary, use AppleTalk to send the file to the Printer. If AppleTalk is not being used to send the Binary file to the Printer, you have to change the PostScript settings to Binary through the Front Panel (Set-up menu / PS settings / Encoding / Binary). 

Solution 3: More information click here

Read More..

Samsung CLX 3175N, FN, FW Printer

Downloads:

Cartridges:

Parts:

Troubleshooting:
Message "replace imaging unit":You have to change the drum (CLT-R409)
Message "System error cycle power":You have to change the photo interruptor.(0604-001095)
How to unlock the scanner (message "Scanner locked"):Hold on "Stop" button during 10 seconds.

Read More..

HP Photosmart and Officejet Printhead

When you've tried all solutions for solving "0xc..." errors and any one works... you have to change the printhead.

HP Print Head Printhead CB326-30002 CN642A for HP 564XL and HP 564

PhotoSmart B8500PhotoSmart B8550PhotoSmart B8553PhotoSmart B8558PhotoSmart C309 SeriesPhotoSmart C309aPhotoSmart C309gPhotoSmart C310aPhotoSmart C510aPhotoSmart C5300PhotoSmart C5324PhotoSmart C5370PhotoSmart C5373PhotoSmart C5380PhotoSmart C5383PhotoSmart C5388PhotoSmart C5390PhotoSmart C5393PhotoSmart C6300PhotoSmart C6324PhotoSmart C6340PhotoSmart C6350PhotoSmart C6375PhotoSmart C6380PhotoSmart C6383PhotoSmart C6388PhotoSmart D5400 SeriesPhotoSmart D5445PhotoSmart D5460PhotoSmart D5463PhotoSmart D5468PhotoSmart D7500 SeriesPhotoSmart D7560PhotoSmart eStation All-in-OnePhotoSmart Fax e-All-in-One - C410aPhotoSmart Premium e-All-in-OnePhotoSmart Premium FaxPhotoSmart Premium Fax All-in-OnePhotoSmart TouchSmart Web All-in-One Printers 
HP 920 printhead CN643A - CD868-3001:
OfficeJet 6500 SeriesOfficeJet 6500 WirelessOfficeJet 7000PhotoSmart B109A B109N B109C B109D B109fPhotoSmart B209 SeriesPhotoSmart Plus

Read More..

How to fix error B200 on canon Printers

The printhead voltage or temperature is not normal.

Solution 1:
Disconnect the power cable from the printer.Wait 1 hour.Connect the power cable
Solution 2:
Check and Clean Head contact pin condition of the carriage unitCheck Cable connection especially the carriage FFC
Solution 3:

Solution 4: 
Replace the power supply unit.
Solution 5:
More information click here

Read More..

Oki C5650, C56250n, C5650dn Printer

Downloads:

Consumables:
Okidata Brand C5500n High Yield Black Toner - 43324404 Okidata 43324401 High-Yield Laser Printer Toner 5000 Page-Yield Yellow Okidata 43324402 High-Yield Laser Printer Toner Type C8 5000 Page-Yield Magenta Okidata 43324403 High Capacity Cyan Toner Cartridge Okidata C5500, C5650, C5800 Series Black Drum (20,000 Yield), Part Number 43381704 Okidata  43381701 Drum unit Yellow For C5650N (Drum/Drum Kit) Okidata C5500, C5650, C5800 Series Magenta Drum (20,000 Yield), Part Number 43381702 Okidata C5500, C5650, C5800 Series Cyan Drum (20,000 Yield), Part Number 43381703 Okidata C5650 Series Transfer Belt Popular High Quality Practical Modern Design
Troubleshooting:
This error indicates that the Image Drum Up/Down Process is not working properly. The errors are as follows:
140 - Yellow Drum Up/Down error
141 - Magenta Drum Up/Down error
142 - Cyan Drum Up/Down error
Solution:
1. Reseat the Image Drums. Ensure they are in seating properly into the drum carriage.
2. Reseat the Toner Cartridges. Ensure they are seating properly into the Image Drums.
3. Reseat the Contact Sensor Spring assembly and inspect it for damage or mis-alignment. If the springs appear bent or dis-lodged reseat them. 1. Turn machine on while pushing and holding the TWO up/down menu buttons at same time.
2. Menu window will show "OKI USER"
3. Scroll to " Engine Dialog Mode" is indicated. Push Enter button.
4. "Diagnostic Mode xx.xx.xx S-Mode is indicated.
5. Scroll to "NV-Ram initial" is indicated. Push ENTER.
6. Window shows "NV-Ram- Initial Table 1".
7. Push ONLINE and ENTER Buttons simultaneously and HOLD for 10 seconds after you see "Executing Reset" appear in menu window.
8. Restart printer. Message error "310/311:Cover Open":1.Open the front door.
2.On the left is about a 3" curved white plastic swing hing guide piece, slotted in the middle.
3.On the metal wall to the left of it is a tab bent out to fit into this groove. If the Tab is not fully in the groove, it will prevent the front door from "fully" closing on this side, preventing it from actuating the switch mentioned by others.

Read More..

How to reset Waste ink Counter on Canon Pixma MP480 printer

After a message error like "Ink Absorber is Full", you need to reset the printer to solve the issue:

Download the resetter software

Power cable and usb cable must be connected

Solution:

1. Turn off the printer without pulling the power cords.
2. Hold down STOP/RESET button and press Power button.
3. Keep holding down Power button and let STOP/RESET button go.
4. Then Press STOP/RESET button twice then let BOTH buttons go.
5. Alternate Blinking error is gone: your are in Service Mode state.
1. Extract the resetter software and double click "MP480.exe" W
2. Click Reload Button and you will get a new USB port.
3. Load some papers in your printer and press the "Main" Button once,
4. Wait until the printing is done.
5. Then press "EEPROM Clear" button to clear EEPROM.
6. Then press EEPROM button and the printer will print some text.
7. Then power off the printer and turn on again.

Read More..

How to solve error 5011 on Canon Printers

This error occurs on these models: MP480, MP490, MX340, MX320, MX350,

Solution 1:
Unplug power supply and plug back in.
Solution 2:
Check for no pieces of paper, no littles objetcs in the printers.
Solution 3:
Carefully clean the encoder strip. It's located behind the carriage that runs all the way from right to left

Read More..

Canon Pixma IP2000 printer

Downloads:


Parts:

Troubleshooting:
Message error "waste ink tank full". You have to reset it:Start with the power off.
Hold down the "On/Off" button plus the "Resume" button at the same time without release them.
Let go of the "Resume" button only.
Then press the "Resume" button twice.
Let go of the "On/Off" button.
Press the "Resume" button 4 times
Press the power button 2 times.
The printer should now be okay and the lights will return to norma. More information click here

Read More..

SSC Service Utility Software to reset Epson printers

SSC Service Utility allow to do many things with Epson printer :

- Work directly with CSIC in Epson Stylus printers cartridges.
- Reset or rewrite any chip using special addon device.
- Freeze internal ink counters.
- Reset internal ink counters even with empty cartridges.
- Separate cleaning of color and black heads for all Epson inkjet printers, powerful cleaning mode.
- Hot swapping of cartridges supported.
- Resetting of protection counter.
- More then 100 different Epson printers supported

The site: http://www.ssclg.com/epsone.shtml

Download the 4.30 version

Printers you can reset with SSC utility:

Epson Stylus ?olor 400/440/480 LPT/480SXU/580/600/640/660/670/680/777/740/760/ 800/850/860/880/900 / EM-900C/980/1160/1520/3000
C20 / C40 / CL-750/C41 / C42 / C43 / C44 / C45 / C46 / C47 / C48/C50/C60/C61
C62 /C63 / C64 /C65 / C66/C67 / C68 / D68/C70/C80/C82/C83 / C84/C85 / C86/C87
C88 / D88 and PE
Photo RX420 / RX425 / RX430 /RX500 / RX510/RX520/RX600 / RX610/RX620/RX700 CX3100 / CX3200/CX3500 / CX3600 / CX3650/CX3700/CX3800 / CX3810 / DX3800/CX4500 CX4600/CX4100 / CX4200 /CX4700 / CX4800/DX4200 / DX4800 /CX5100 / CX5200 /CX5300 / CX5400 CX6400 / CX6600 /CX6300 / CX6500 /CX7800 Photo /Photo EX /Photo 700 / IP-100/750 / PM-770C /780 / 790 /
PM-780C /810 / 820
Photo 820 /825 / 915/830 / 830U/870 / PM-875DC /R200 / R210/R220 / R230
R300 / R310 / Photo R320/R800 / PX-G900/R1800/R2400/890/PM-890C/PM-A700
PM-G720/PM-970C/895/ 785EPX
Photo 900 /925 / 935/ 950 / 960 / PM-950C/1200 / PM-3000C/1270 / PM-3300C/1280 / PM-3500C
Photo 1290/2000P/2100/2200 / PM-4000EPX/Pro 5000 / PM-5000C

More information click here

Read More..

How to solve error 16H on Konica 2300, 2300DL

Solution:
Turn off the printer. Open the panel door exposing the toner waste container and cartridge access area. Gently pry away the waste toner container from the printer.  Put the waste toner powder into a garbage bag.There are two manual screws holding the transfer belt component securely. One is on the left upper part, one is on the right. They are designed to loosen, but stay attached to the transfer belt component. Flip the large blue handle with the arrow upward.Look for a portuding squarish handle below the larger blue handle transfer belt component. Look caredfully at the diagram on this little handle. You must squeeze the level on the underside of this squarish handle to unlock it. Once unlocked you carefully slide this part out. Put this whole component aside for later assembly back in.Carefully slide out the larger transfer belt component about 2/3 of the way out. You should see a pale green plastic handle on the top of this part. You can grab that handle to assist you to remove the part completely from the printer. At the end of sliding the component outward you will need to carefully angle the part upward because there is a metal guide track at the upper most portion of the part which will prevent the part from disengagin from the track unless you angle the part upward at the very end of the slide. Examine the somewhat shiny plasticky belt to be not torn, damaged or dirty...
Angle the transfer belt part upward (the end closest to you goes upward) and guide the part onto the metal guide track at the upper portion of the printer. Slide the component in.
Tighten the two hand-screws. Slide the shiny green cynliner component back in. Make sure to squeeze the underside of that squarish handle at the final insertion because that permits the component to seat properly and lock in place.Flip the large blue handle back into the down position as before we started this process.Vacuum the two spots where the waste toner container port holes fit into. Put the waste toner container back into position.Close the door. Turn on the printer.

Read More..

Error message Service Req E020 on Epson printers

This error could appears on these models: EPL-N3000, Aculaser C1100, Aculaser C1900...

Solution 1: “Secondary transfer voltage contact/release problem”
Some electric parts can cause the trouble: Transfer Roller Pressure Solenoid (SL2) Transfer Roller Pressure Position Detection Sensor (PC7) Engine Board (PWB-A)  
Solution 2:
The problem come from the fuser. You have to replace it.EPL-N3000: C13S053017BA Aculaser  C1100: 2090471Aculaser C1900: 2077368

More information click here

Read More..

How to reset drum counter on Oki B4400

Solution to reset the drum counter:
Open the Status Monitor.Click "Printer Setup" then "Open Configuration" and "Maintenance".Click Drum Counter Reset. Click Apply.Click OK

Réinitialiser le compteur du tambour
Ouvir le Status Monitor.Cliquer sur "Printer Setup" puis "Open Configuration" et "Maintenance".Cliquer sur Drum Counter Reset (Réinitialiser le compteur du tambour). Cliquer Apply (appliquer).Cliquer sur OK
Cero el contador del cilindro Abras Status Monitor.Clic en "Printer Setup" y "Open Configuration" y "Maintenance".Clic en Drum Counter Reset. Clic Apply (aplicar).Clic OK
Reiniciar o contador do cilindro Lance o Status Monitor.Clique com "Printer Setup", "Open Configuration", "Maintenance".Clique com Drum Counter Reset. Clique Apply (aplicar).Clique OK

Read More..

how to reset counter after tranfer belt and fuser replacement on clx2160n

Resetting the transfert belt's counter after replacement (CLP-300 Imaging Kit):
Press: Menu, #1934, Menu,
"Tech Mode" --> OK, 
"Data Setup" --> OK,
go to "Clear Counts" --> OK,
"Enter Password [????]" --> 1934, OK,
"Clear Counts [Total Page CNT]", go to "[Imaging Unit]" --> OK,
"Clearing…", --> Back.

Resetting the fuser's counter after replacement (JC96-03609A):
Press: Menu, #1934, Menu,
"Tech Mode" --> OK,
"Data Setup" --> OK,
go to "Clear Counts" --> OK,
"Enter Password [????]" --> 1934, OK,
"Clear Counts [Total Page CNT]", go to "[Fuser]" --> OK,
"Clearing…", --> Back.
More information click here

Read More..